MicroPython: OLED Display with ESP32 and ESP8266

In this guide, you’ll learn how to use the 0.96 inch SSD1306 OLED display with an ESP32 or ESP8266 using MicroPython firmware. As an example, we’ll show you how to display a simple ‘Hello, World!’ message. Later, we’ll also show you how to use other useful functions to interact with the OLED display.

oled display esp8266 esp32 micropython

You might also like reading our dedicated guides for ESP with OLED display using Arduino IDE:

Prerequisites

To follow this tutorial you need MicroPython firmware installed in your ESP32 or ESP8266 boards. You also need an IDE to write and upload the code to your board. We suggest using Thonny IDE or uPyCraft IDE:

Learn more about MicroPython: MicroPython Programming with ESP32 and ESP8266 eBook

Introducing the OLED display

In this guide we’ll use the 0.96 inch SSD1306 OLED display that is 128×64 pixels and uses I2C communication protocol.

ssd1306 0.96inch i2c oled display

I2C communication

For the I2C OLED display, these are the connections you need to make:

OLEDESP32ESP8266
Vin3.3V3.3V
GNDGNDGND
SCLGPIO 22GPIO 5 (D1)
SDAGPIO 21GPIO 4 (D2)

Parts Required

Here’s a list of parts you need for this project:

You can use the preceding links or go directly to MakerAdvisor.com/tools to find all the parts for your projects at the best price!

Schematic – ESP32

Follow the next schematic diagram if you’re using an ESP32 board:

oled display with esp32 micropython

Recommended reading: ESP32 Pinout Reference Guide

Schematic – ESP8266

Follow the next schematic diagram if you’re using an ESP8266 board:

esp8266 oled display micropython

Recommended reading: ESP8266 Pinout Reference Guide

SSD1306 OLED Library

The library to write to the OLED display isn’t part of the standard MicroPython library by default. So, you need to upload the library to your ESP32/ESP8266 board.

# MicroPython SSD1306 OLED driver, I2C and SPI interfaces created by Adafruit

import time
import framebuf

# register definitions
SET_CONTRAST        = const(0x81)
SET_ENTIRE_ON       = const(0xa4)
SET_NORM_INV        = const(0xa6)
SET_DISP            = const(0xae)
SET_MEM_ADDR        = const(0x20)
SET_COL_ADDR        = const(0x21)
SET_PAGE_ADDR       = const(0x22)
SET_DISP_START_LINE = const(0x40)
SET_SEG_REMAP       = const(0xa0)
SET_MUX_RATIO       = const(0xa8)
SET_COM_OUT_DIR     = const(0xc0)
SET_DISP_OFFSET     = const(0xd3)
SET_COM_PIN_CFG     = const(0xda)
SET_DISP_CLK_DIV    = const(0xd5)
SET_PRECHARGE       = const(0xd9)
SET_VCOM_DESEL      = const(0xdb)
SET_CHARGE_PUMP     = const(0x8d)


class SSD1306:
    def __init__(self, width, height, external_vcc):
        self.width = width
        self.height = height
        self.external_vcc = external_vcc
        self.pages = self.height // 8
        # Note the subclass must initialize self.framebuf to a framebuffer.
        # This is necessary because the underlying data buffer is different
        # between I2C and SPI implementations (I2C needs an extra byte).
        self.poweron()
        self.init_display()

    def init_display(self):
        for cmd in (
            SET_DISP | 0x00, # off
            # address setting
            SET_MEM_ADDR, 0x00, # horizontal
            # resolution and layout
            SET_DISP_START_LINE | 0x00,
            SET_SEG_REMAP | 0x01, # column addr 127 mapped to SEG0
            SET_MUX_RATIO, self.height - 1,
            SET_COM_OUT_DIR | 0x08, # scan from COM[N] to COM0
            SET_DISP_OFFSET, 0x00,
            SET_COM_PIN_CFG, 0x02 if self.height == 32 else 0x12,
            # timing and driving scheme
            SET_DISP_CLK_DIV, 0x80,
            SET_PRECHARGE, 0x22 if self.external_vcc else 0xf1,
            SET_VCOM_DESEL, 0x30, # 0.83*Vcc
            # display
            SET_CONTRAST, 0xff, # maximum
            SET_ENTIRE_ON, # output follows RAM contents
            SET_NORM_INV, # not inverted
            # charge pump
            SET_CHARGE_PUMP, 0x10 if self.external_vcc else 0x14,
            SET_DISP | 0x01): # on
            self.write_cmd(cmd)
        self.fill(0)
        self.show()

    def poweroff(self):
        self.write_cmd(SET_DISP | 0x00)

    def contrast(self, contrast):
        self.write_cmd(SET_CONTRAST)
        self.write_cmd(contrast)

    def invert(self, invert):
        self.write_cmd(SET_NORM_INV | (invert & 1))

    def show(self):
        x0 = 0
        x1 = self.width - 1
        if self.width == 64:
            # displays with width of 64 pixels are shifted by 32
            x0 += 32
            x1 += 32
        self.write_cmd(SET_COL_ADDR)
        self.write_cmd(x0)
        self.write_cmd(x1)
        self.write_cmd(SET_PAGE_ADDR)
        self.write_cmd(0)
        self.write_cmd(self.pages - 1)
        self.write_framebuf()

    def fill(self, col):
        self.framebuf.fill(col)

    def pixel(self, x, y, col):
        self.framebuf.pixel(x, y, col)

    def scroll(self, dx, dy):
        self.framebuf.scroll(dx, dy)

    def text(self, string, x, y, col=1):
        self.framebuf.text(string, x, y, col)


class SSD1306_I2C(SSD1306):
    def __init__(self, width, height, i2c, addr=0x3c, external_vcc=False):
        self.i2c = i2c
        self.addr = addr
        self.temp = bytearray(2)
        # Add an extra byte to the data buffer to hold an I2C data/command byte
        # to use hardware-compatible I2C transactions.  A memoryview of the
        # buffer is used to mask this byte from the framebuffer operations
        # (without a major memory hit as memoryview doesn't copy to a separate
        # buffer).
        self.buffer = bytearray(((height // 8) * width) + 1)
        self.buffer[0] = 0x40  # Set first byte of data buffer to Co=0, D/C=1
        self.framebuf = framebuf.FrameBuffer1(memoryview(self.buffer)[1:], width, height)
        super().__init__(width, height, external_vcc)

    def write_cmd(self, cmd):
        self.temp[0] = 0x80 # Co=1, D/C#=0
        self.temp[1] = cmd
        self.i2c.writeto(self.addr, self.temp)

    def write_framebuf(self):
        # Blast out the frame buffer using a single I2C transaction to support
        # hardware I2C interfaces.
        self.i2c.writeto(self.addr, self.buffer)

    def poweron(self):
        pass


class SSD1306_SPI(SSD1306):
    def __init__(self, width, height, spi, dc, res, cs, external_vcc=False):
        self.rate = 10 * 1024 * 1024
        dc.init(dc.OUT, value=0)
        res.init(res.OUT, value=0)
        cs.init(cs.OUT, value=1)
        self.spi = spi
        self.dc = dc
        self.res = res
        self.cs = cs
        self.buffer = bytearray((height // 8) * width)
        self.framebuf = framebuf.FrameBuffer1(self.buffer, width, height)
        super().__init__(width, height, external_vcc)

    def write_cmd(self, cmd):
        self.spi.init(baudrate=self.rate, polarity=0, phase=0)
        self.cs.high()
        self.dc.low()
        self.cs.low()
        self.spi.write(bytearray([cmd]))
        self.cs.high()

    def write_framebuf(self):
        self.spi.init(baudrate=self.rate, polarity=0, phase=0)
        self.cs.high()
        self.dc.high()
        self.cs.low()
        self.spi.write(self.buffer)
        self.cs.high()

    def poweron(self):
        self.res.high()
        time.sleep_ms(1)
        self.res.low()
        time.sleep_ms(10)
        self.res.high()

View raw code

Follow the next set of instructions for the IDE you’re using:

  • A. Upload OLED library with uPyCraft IDE
  • B. Upload OLED library with Thonny IDE

A. Upload OLED library with uPyCraft IDE

This section shows how to upload a library using uPyCraft IDE. If you’re using Thonny IDE, read the next section.

1. Create a new file by pressing the New File button.

2. Copy the OLED library code into that file. The OLED library code can be found here.

Note: the SSD1306 OLED display library was built by Adafruit and will no longer
be updated. At the moment, it works fine. However, we’ll update this guide if we
find a similar library that works as well as this one.

3. After copying the code, save the file by pressing the Save button.

4. Call this new file “ssd1306.py” and press ok.

import library upycraft ide save file

5. Click the Download and Run button.

The file should be saved on the device folder with the name “ssd1306.py” as
highlighted in the following figure.

import save library uPyCraft IDE script file

Now, you can use the library functionalities in your code by importing the library.

B. Upload OLED library with Thonny IDE

If you’re using Thonny IDE, follow the next steps:

1. Create a new file in Thonny IDE and copy the library code. The OLED library code can be found here.

2. Go to File > Save as and select MicroPython device.

Thonny IDE Save to MicroPython Device

3. Name the file ssd1306.py and click OK to save the file on the ESP Filesystem.

And that’s it. The library was uploaded to your board. Now, you can use the library functionalities in your code by importing the library.

Code

After uploading the library to the ESP32 or ESP8266, copy the following code to the
main.py file. It simply prints the ‘Hello, World!‘ message three times in the display.

# Complete project details at https://RandomNerdTutorials.com/micropython-programming-with-esp32-and-esp8266/

from machine import Pin, SoftI2C
import ssd1306
from time import sleep

# ESP32 Pin assignment 
i2c = SoftI2C(scl=Pin(22), sda=Pin(21))

# ESP8266 Pin assignment
#i2c = SoftI2C(scl=Pin(5), sda=Pin(4))

oled_width = 128
oled_height = 64
oled = ssd1306.SSD1306_I2C(oled_width, oled_height, i2c)

oled.text('Hello, World 1!', 0, 0)
oled.text('Hello, World 2!', 0, 10)
oled.text('Hello, World 3!', 0, 20)
        
oled.show()

View raw code

How the Code Works

Start by importing the necessary modules to interact with the GPIOs and send data to the OLED via I2C communication. You need to import the Pin and SoftI2C classes from the machine module.

from machine import Pin, SoftI2C

You also need to import the OLED library that you previously uploaded to the board as ssd1306.py file.

import ssd1306

The ESP32 default I2C pins are GPIO 22 (SCL) and GPIO 21 (SDA). The ESP8266 default I2C pins are GPIO 5 (SLC) and GPIO 4 (SDA).

Use the following line if you’re using an ESP32 board:

# ESP32 Pin assignment 
i2c = SoftI2C(scl=Pin(22), sda=Pin(21))

Comment the previous line and uncomment the following if you’re using an ESP8266 board:

#ESP8266 Pin assignment
i2c = SoftI2C(scl=Pin(5), sda=Pin(4))

Define the OLED width and height on the following variables:

oled_width = 128
oled_height = 64

After that, create an SSD1306_I2C object called oled. This object accepts the OLED width, height, and the I2C pins you’ve defined earlier.

oled = ssd1306.SSD1306_I2C(oled_width, oled_height, i2c)

After initializing the OLED display, you just need to use the text() function on the oled object to write text. After the text() function, you need to call the show() method to update the OLED.

oled.text('Hello, World 1!', 0, 0)
oled.text('Hello, World 2!', 0, 10)
oled.text('Hello, World 3!', 0, 20)
oled.show()

The text() method accepts the following arguments (in this order):

  • Message: must be of type String
  • X position: where the text starts
  • Y position: where the text is displayed vertically
  • Text color: it can be either black or white. The default color is white and this parameter is optional.
    • 0 = black
    • 1 = white

For example, the following line writes the ‘Hello, World 1!’ message in white color. The text starts on x = 0 and y = 0.

oled.text('Hello, World 1!', 0, 0)

The next line of code writes the text on the next line (y =10).

oled.text('Hello, World 2!', 0, 10)

Finally, for the changes to take effect, use the show() method on the oled object.

oled.show()

Demonstration

Upload the code to your board. Your OLED display should look as follows:

oled display text esp8266 esp32 micropython

Other OLED functions

The library provides other methods to interact with the OLED display.

Fill the screen

To fill the entire screen with white, use the fill() function as follows:

oled.fill(1)
oled.show()
oled fill white screen esp8266 esp32 micropython

To clear the screen use the fill() method as pass 0 as argument. (Sets all pixels to black):

oled.fill(0)
oled.show()

Draw a pixel

To draw a pixel, use the pixel() method, followed by the show() method. The pixel() method accepts the following arguments:

  • X coordinate: pixel location horizontally
  • Y coordinate: pixel location vertically
  • Pixel color: can be black or white
    • 0 = black
    • 1 = white

For example, to draw a white pixel on the top left corner:

oled.pixel(0, 0, 1)
oled.show()
oled display a pixel esp8266 esp32 micropython

Invert colors

You can also invert the OLED colors: white with black and vice versa, using the invert() method:

oled.invert(True)
oled invert colors esp8266 esp32 micropython

To get back to the original colors, use:

oled.invert(False)

Displaying data from sensors

The text() function only accepts variables of type String as a message. Sensor readings are usually stored in int or float variables.

If you want to display sensor readings and they are stored in int or float variables, they should be converted to a String. To convert the data to a string you can use the str() function:

temperature = 12.34
temperature_string = str(temperature)

Then, you can display the temperature_string variable on the OLED using the text() and show() methods:

oled.text(temperature_string, 0, 0)
oled.show()

Wrapping Up

This quick guide showed you how to use the OLED basic functionalities: write text and draw pixels with the ESP32 and ESP8266 using MicroPython. Now, you can use the OLED in your own projects to display messages, or sensor readings.

We have other MicroPython tutorials that you might also like:

If you want to learn more about programming the ESP32 and ESP8266 boards with MicroPython, take a look our eBook: MicroPython Programming with ESP32 and ESP8266.



Learn how to build a home automation system and we’ll cover the following main subjects: Node-RED, Node-RED Dashboard, Raspberry Pi, ESP32, ESP8266, MQTT, and InfluxDB database DOWNLOAD »
Learn how to build a home automation system and we’ll cover the following main subjects: Node-RED, Node-RED Dashboard, Raspberry Pi, ESP32, ESP8266, MQTT, and InfluxDB database DOWNLOAD »

Enjoyed this project? Stay updated by subscribing our newsletter!

49 thoughts on “MicroPython: OLED Display with ESP32 and ESP8266”

  1. Thanks a lot for the great tutorial. Everything worked for me right away!

    I still have a question:

    Is it possible to use a different font with the given driver “ssd1306.py”?

    Reply
  2. I followed this tutorial. I am using a wemos D1 mini. I am using esp8266-20190529-v1.11.bin firmware. I have no problem with the led blink code. When I tried using with the OLED, i get this error – OSError: [Errno 110] ETIMEDOUT. I have no idea how to solve it. With the same OLED and code( just modify the scl and sda pins), I tried on an esp32, it is working. Anyone facing the same problem with wemos D1 mini?

    Reply
    • Hi Mikele.
      That’s great!
      I’m always happy to see our readers’ results.
      I’ve also watched some of your other projects using our tutorials.
      Keep up the good work 😀
      Regards,
      Sara

      Reply
  3. The initialization from this guide didn’t work for me. I used directly from micropython reference for ESP8266 and it work fine:
    i2c = I2C(scl=Pin(5), sda=Pin(4), freq=400000)

    Can u tell me how to clear screen before updating it with new data in loop ? I’m reading the temperature and I want to update it but firstly I have to clear screen because after few updates the it’s unreadable. Some tip ?

    Reply
  4. Hi there,

    when I uploade the code to my ESP 32 it shows the following error message:

    download ok
    ex& J<moduleZ”ssd1306.py”, line 123, in write_cmd
    OSError: [Errno 110] ETIMEDOUT

    There seems to be a problem with the initialization. Any Ideas?
    Best regards
    Martin

    Reply
  5. Thank you for writing this tutorial! It was a great way to introduce myself to the ESP32 and using it with an OLED display.

    I ended up abandoning the adafruit driver in favor of the micropython supported driver (https://github.com/micropython/micropython/blob/master/drivers/display/ssd1306.py). They are substantially similar, but I found the latter, with its simple ability to use fill_rect() and rect() much easier to work with (I never figured out how to update a single value on the screen without having to use fill(0) in the adafruit driver, and wasn’t a fan of the flashing it caused).

    Other than the change-up of the driver, this tutorial really helped me get started with the ESP32. Thanks again!

    Reply
      • Great! I’d love to hear your thoughts on it.

        The code you wrote above should work with only minor changes: in terms of function calls for text(), you just need add a parameter for color at the end of each call (binary of 0 or 1), but otherwise all of the commands you already have listed will work.

        Also worthy of note, it would seem that since this tutorial was written, the I2C library has been deprecated in favor of SoftI2C. The code you wrote will absolutely work as is, but the debugger will issue a warning about the deprecation.

        Again, this only requires minor changes: importing the SoftI2C from machine instead of I2C, and dropping the -1 parameter from the class initialization.

        I hope I’m not coming across as critical, I found this tutorial extremely useful, and just trying to share some of my discoveries while playing with what you taught me.

        Reply
        • Hi Tim.
          Thank you for pointing that out.
          I also noticed that the I2C being deprecated. We’ll need to update all our tutorials that use I2C.
          Your feedback is very important so that we can improve our tutorials.
          Thank you.
          Regards,
          Sara

          Reply
  6. but i still, cant use library for rasp pico because it is not library for pico.
    Traceback (most recent call last):
    File “”, line 13, in
    File “ssd1306.py”, line 116, in init
    File “ssd1306.py”, line 36, in init
    File “ssd1306.py”, line 61, in init_display
    File “ssd1306.py”, line 121, in write_cmd

    Reply
  7. I am very much interested in Micropython, though far from it except Blink. I have inspired and did many projects from your newsletter in Arduino and achieved success. should I use SSD1307 instead of SSD1306? If not what should be the right code. If possible plz. help me out.

    Reply
  8. Excellent tutorial! I got a “Micropython starter kit” which had the exact same boards: an ESP32, an SDD1306, and a DHT11. I was afraid that at least the OLED module didn’t work since it didn’t seem to power up whether I connected it to the ESP32, or direct to the breadboard. I think it was uploading ssd1306.py to the board that brought it to life, and I got “Hello World” displayed on it.

    I also appended your code for the DHT11 to main.py, modifying it to send output to the OLED module instead. After a little futzing with the parameters to oled.text, the temperature and humidity show up below the Hello World strings.

    Next up: a nicer format instead of the bare numbers, and installing larger fonts so the numbers take up more of the screen. The “Hello World” strings can go

    Reply
  9. non funzio questi sono gli errori
    Traceback (most recent call last):
    File “”, line 15, in
    File “ssd1306.py”, line 116, in init
    File “ssd1306.py”, line 36, in init
    File “ssd1306.py”, line 61, in init_display
    File “ssd1306.py”, line 121, in write_cmd
    OSError: [Errno 19] ENODEV

    >

    Reply
  10. oled = ssd1306.SSD1306_I2C(oled_width, oled_height, i2c)

    Traceback (most recent call last):
    File “”, line 10, in
    AttributeError: ‘module’ object has no attribute ‘SSD1306_I2C’

    Reply
  11. Hi Sara,
    Thanks for the above.
    Can I use this connection and OLED device to display an image on the OLED screen?
    We would like to display QR code on the screen which we will have as a BMP file available for the ESP.
    Thanks,
    Eyal

    Reply
    • Hi.
      they changed the IDE.
      Go to File > Save as… or click on the save icon
      Select MicroPython device.

      I hope this helps.
      Regards,
      Sara

      Reply
  12. I erased the flash, installed the latest Micropython (1.20.0) using Thonny, and copied your code from this web page. I get the “OSError: [Errno 110] ETIMEDOUT” error.

    This exact same hardware works with Arduino IDE code.

    I’m using a D1 Mini 8266 and SSD1306 display.

    I would appreciate your help. Thanks…

    Reply
    • Hi.
      Double-check that the OLED display is properly connected to your board.
      Also, make sure that you’ve uncommented the line to use ESP8266 I2C pins:
      i2c = SoftI2C(scl=Pin(5), sda=Pin(4))

      Regards.
      Sara

      Reply
      • The display works when programmed by Arduino IDE.
        The pins are connected correctly using code copied from this page.

        Does this will help?
        [Micropython]

        from machine import I2C
        i2c.scan()
        []

        [Arduino example I2CScanner / Scanner]
        — Scan started —
        I2C device found at address 0x3C !
        — Scan finished —

        Reply
  13. That is the right address, but it was found by an Arduino scan.
    The scan of the same hardware with micropython does not show any I2C devices.
    from machine import I2C
    i2c.scan()
    []

    Yes, I uncommented the I2C pins for the 8266 as shown below.

    ESP8266 Pin assignment

    i2c = SoftI2C(scl=Pin(5), sda=Pin(4))

    Thanks.

    Reply
  14. Help pleace !

    %Run -c $EDITOR_CONTENT

    MPY: soft reboot
    Traceback (most recent call last):
    File “”, line 13, in
    File “ssd1306.py”, line 116, in init
    File “ssd1306.py”, line 36, in init
    File “ssd1306.py”, line 61, in init_display
    File “ssd1306.py”, line 121, in write_cmd
    OSError: [Errno 19] ENODEV

    >

    Reply
  15. My OLED supports different font sizes, and the default is very small. I know that because I did that on c (ino) code on arduino ide. Is there a way to tell it to use a larger font with micropython?

    Reply
  16. Hallo Sara,
    vielen Dank für die tollen Tutorials. Habe dadurch sehr viel Spaß mit MicroPython und dem ESP32. Konnte viele Erfahrungen sammeln und manches Problem selbst lösen.
    Mit dem OLED Display ssd1306 habe ich ein größeres Problem.
    Es wir nun schwarzer Schnee auf hellem Grund angezeigt, statt der Worte “Hello World”.
    Ich habe sowohl die hier empfohlene Lib. zu ssd1306, wie auch die auf git.hub ausprobiert, sogar 2 andere Displays, aber es bleibt bei der Anzeige von Schnee statt Schrift. Das “Schneebild” ist sehr konstant. Markante Muster ändern sich nicht. Es scheint, wie eine zerrissene Anzeige der Textausgabe. Kannst Du bitte helfen?
    Mit bestem Dank vorab
    Manfred

    Reply
  17. hi!!
    I have this problem and I can´t solve it. Can you help me?

    Traceback (most recent call last):
    File “”, line 15, in
    File “ssd1306.py”, line 114, in init
    File “ssd1306.py”, line 34, in init
    File “ssd1306.py”, line 59, in init_display
    File “ssd1306.py”, line 119, in write_cmd
    OSError: [Errno 116] ETIMEDOUT

    >

    Reply
  18. Hello Sara,

    Thank you very much for the great tutorials. I’ve had a lot of fun with MicroPython and the ESP32 as a result. I’ve gained a lot of experience and have been able to solve many problems on my own.

    I’m facing a bigger issue with the OLED display ssd1306. Instead of displaying the words “Hello World,” it’s showing black snow on a light background. I’ve tried both the recommended library for ssd1306 and the one on GitHub, even with two other displays, but it still shows snow instead of text. The “snow image” is very consistent, and distinctive patterns don’t change. It seems like a distorted display of text output. Can you please help?

    Thanks in advance.

    Best regards,
    Manfred

    Reply
      • Yes, I did .
        Thank you for answering. I checked everything carefully.
        Many other tutorials worked pretty fine. Just the Display is not working well.
        I will double check all settings again.

        Best Regards
        Manfred

        Reply
        • It seems like the display is running the default code and that it is not running the current code.
          Make sure to upload the code as main.py and restart the ESP32 afterwards.
          Regards,
          Sara

          Reply
  19. Traceback (most recent call last):
    File “”, line 14, in
    File “ssd1306.py”, line 116, in init
    File “ssd1306.py”, line 36, in init
    File “ssd1306.py”, line 61, in init_display
    File “ssd1306.py”, line 121, in write_cmd
    OSError: [Errno 19] ENODEV

    May help me?

    Reply
    • Hi.
      Check that you’ve installed the library following the instructions in our guide.
      Double-check your display connections.
      Regards,
      Sara

      Reply

Leave a Reply to Daniel Escasa Cancel reply

Download Our Free eBooks and Resources

Get instant access to our FREE eBooks, Resources, and Exclusive Electronics Projects by entering your email address below.