This project shows how to connect the TTGO T-Call ESP32 SIM800L board to the Internet using a SIM card data plan and publish data to the cloud without using Wi-Fi. We’ll program this board with Arduino IDE.
Watch the Video Tutorial
You can watch the video tutorial or continue reading for the complete project instructions.
Introducing the TTGO T-Call ESP32 SIM800L
The TTGO T-Call is a new ESP32 development board that combines a SIM800L GSM/GPRS module. You can get if for approximately $11.
Besides Wi-Fi and Bluetooth, you can communicate with this ESP32 board using SMS or phone calls and you can connect it to the internet using your SIM card data plan. This is great for IoT projects that don’t have access to a nearby router.
Important: the SIM800L works on 2G networks, so it will only work in your country, if 2G networks are available. Check if you have 2G network in your country, otherwise it won’t work.
To use the capabilities of this board you need to have a nano SIM card with data plan and a USB-C cable to upload code to the board.
The package includes some header pins, a battery connector, and an external antenna that you should connect to your board.
However, we had some issues with that antenna, so we decided to switch to another type of antenna and all the problems were solved. The following figure shows the new antenna.
Project Overview
The idea of this project is to publish sensor data from anywhere to any cloud service that you want. The ESP32 doesn’t need to have access to a router via Wi-Fi, because we’ll connect to the internet using a SIM card data plan.
In a previous project, we’ve created our own server domain with a database to plot sensor readings in charts that you can access from anywhere in the world.
In this project, we’ll publish sensor readings to that server. You can publish your sensor readings to any other service, like ThingSpeak, IFTTT, etc…
If you want to follow this exact project, you should follow that previous tutorial first to prepare your own server domain. Then, upload the code provided in this project to your ESP32 board.
In summary, here’s how the project works:
- The T-Call ESP32 SIM800L board is in deep sleep mode.
- It wakes up and connects to the internet using your SIM card data plan.
- It publishes the sensor readings to the server and goes back to sleep.
In our example, the sleep time is 60 minutes, but you can easily change it in the code.
We’ll be using a BME280 sensor, but you should be able to use any other sensor that best suits your needs.
Hosting Provider
If you don’t have a hosting account, I recommend signing up for Bluehost, because they can handle all the project requirements. If you don’t have a hosting account, I would appreciate if you sign up for Bluehost using my link. Which doesn’t cost you anything extra and helps support our work.
Get Hosting and Domain Name with Bluehost »
Prerequisites
1. ESP32 add-on Arduino IDE
We’ll program the ESP32 using Arduino IDE. So, you need to have the ESP32 add-on installed in your Arduino IDE. Follow the next tutorial, if you haven’t already.
2. Preparing your Server Domain
In this project we’ll show you how to publish data to any cloud service. We’ll be using our own server domain with a database to publish all the data, but you can use any other service like ThingSpeak, IFTTT, etc…
If you want to follow this exact project, you should follow the next tutorial to prepare your own server domain.
3. SIM Card with data plan
To use the TTGO T-Call ESP32 SIM800L board, you need a nano SIM card with a data plan. We recommend using a SIM card with a prepaid or monthly plan, so that you know exactly how much you’ll spend.
4. APN Details
To connect your SIM card to the internet, you need to have your phone plan provider APN details. You need the domain name, username and a password.
In my case, I’m using vodafone Portugal. If you search for GPRS APN settings followed by your phone plan provider name, (in my case its: “GPRS APN vodafone Portugal”), you can usually find in a forum or in their website all the information that you need.
I’ve found this website that can be very useful to find all the information you need.
It might be a bit tricky to find the details if you don’t use a well known provider. So, you might need to contact them directly.
5. Libraries
You need to install these libraries to proceed with this project: Adafruit_BME280, Adafruit_Sensor and TinyGSM. Follow the next instructions to install these libraries.
Installing the Adafruit BME280 Library
Open your Arduino IDE and go to Sketch > Include Library > Manage Libraries. The Library Manager should open.
Search for “adafruit bme280 ” on the Search box and install the library.
Installing the Adafruit Sensor Library
To use the BME280 library, you also need to install the Adafruit_Sensor library. Follow the next steps to install the library in your Arduino IDE:
Go to Sketch > Include Library > Manage Libraries and type “Adafruit Unified Sensor” in the search box. Scroll all the way down to find the library and install it.
Installing the TinyGSM Library
In the Arduino IDE Library Manager search for TinyGSM. Select the TinyGSM library by Volodymyr Shymanskyy.
After installing the libraries, restart your Arduino IDE.
Parts Required
To build this project, you need the following parts:
- TTGO T-Call ESP32 SIM800L
- USB-C cable
- Antenna (optional)
- BME280 sensor module (Guide for BME280 with ESP32)
- Breadboard
- Jumper wires
You can use the preceding links or go directly to MakerAdvisor.com/tools to find all the parts for your projects at the best price!
Schematic Diagram
Wire the BME280 to the T-Call ESP32 SIM800L board as shown in the following schematic diagram.
We’re connecting the SDA pin to GPIO 18 and the SCL pin to GPIO 19. We’re not using the default I2C GPIOs because they are being used by the battery power management IC of the T-Call ESP32 SIM800L board.
Code
Copy the following code to your Arduino IDE but don’t upload it yet. First, you need to make some modifications to make it work.
/*
Rui Santos
Complete project details at https://RandomNerdTutorials.com/esp32-sim800l-publish-data-to-cloud/
Permission is hereby granted, free of charge, to any person obtaining a copy
of this software and associated documentation files.
The above copyright notice and this permission notice shall be included in all
copies or substantial portions of the Software.
*/
// Your GPRS credentials (leave empty, if not needed)
const char apn[] = ""; // APN (example: internet.vodafone.pt) use https://wiki.apnchanger.org
const char gprsUser[] = ""; // GPRS User
const char gprsPass[] = ""; // GPRS Password
// SIM card PIN (leave empty, if not defined)
const char simPIN[] = "";
// Server details
// The server variable can be just a domain name or it can have a subdomain. It depends on the service you are using
const char server[] = "example.com"; // domain name: example.com, maker.ifttt.com, etc
const char resource[] = "/post-data.php"; // resource path, for example: /post-data.php
const int port = 80; // server port number
// Keep this API Key value to be compatible with the PHP code provided in the project page.
// If you change the apiKeyValue value, the PHP file /post-data.php also needs to have the same key
String apiKeyValue = "tPmAT5Ab3j7F9";
// TTGO T-Call pins
#define MODEM_RST 5
#define MODEM_PWKEY 4
#define MODEM_POWER_ON 23
#define MODEM_TX 27
#define MODEM_RX 26
#define I2C_SDA 21
#define I2C_SCL 22
// BME280 pins
#define I2C_SDA_2 18
#define I2C_SCL_2 19
// Set serial for debug console (to Serial Monitor, default speed 115200)
#define SerialMon Serial
// Set serial for AT commands (to SIM800 module)
#define SerialAT Serial1
// Configure TinyGSM library
#define TINY_GSM_MODEM_SIM800 // Modem is SIM800
#define TINY_GSM_RX_BUFFER 1024 // Set RX buffer to 1Kb
// Define the serial console for debug prints, if needed
//#define DUMP_AT_COMMANDS
#include <Wire.h>
#include <TinyGsmClient.h>
#ifdef DUMP_AT_COMMANDS
#include <StreamDebugger.h>
StreamDebugger debugger(SerialAT, SerialMon);
TinyGsm modem(debugger);
#else
TinyGsm modem(SerialAT);
#endif
#include <Adafruit_Sensor.h>
#include <Adafruit_BME280.h>
// I2C for SIM800 (to keep it running when powered from battery)
TwoWire I2CPower = TwoWire(0);
// I2C for BME280 sensor
TwoWire I2CBME = TwoWire(1);
Adafruit_BME280 bme;
// TinyGSM Client for Internet connection
TinyGsmClient client(modem);
#define uS_TO_S_FACTOR 1000000UL /* Conversion factor for micro seconds to seconds */
#define TIME_TO_SLEEP 3600 /* Time ESP32 will go to sleep (in seconds) 3600 seconds = 1 hour */
#define IP5306_ADDR 0x75
#define IP5306_REG_SYS_CTL0 0x00
bool setPowerBoostKeepOn(int en){
I2CPower.beginTransmission(IP5306_ADDR);
I2CPower.write(IP5306_REG_SYS_CTL0);
if (en) {
I2CPower.write(0x37); // Set bit1: 1 enable 0 disable boost keep on
} else {
I2CPower.write(0x35); // 0x37 is default reg value
}
return I2CPower.endTransmission() == 0;
}
void setup() {
// Set serial monitor debugging window baud rate to 115200
SerialMon.begin(115200);
// Start I2C communication
I2CPower.begin(I2C_SDA, I2C_SCL, 400000);
I2CBME.begin(I2C_SDA_2, I2C_SCL_2, 400000);
// Keep power when running from battery
bool isOk = setPowerBoostKeepOn(1);
SerialMon.println(String("IP5306 KeepOn ") + (isOk ? "OK" : "FAIL"));
// Set modem reset, enable, power pins
pinMode(MODEM_PWKEY, OUTPUT);
pinMode(MODEM_RST, OUTPUT);
pinMode(MODEM_POWER_ON, OUTPUT);
digitalWrite(MODEM_PWKEY, LOW);
digitalWrite(MODEM_RST, HIGH);
digitalWrite(MODEM_POWER_ON, HIGH);
// Set GSM module baud rate and UART pins
SerialAT.begin(115200, SERIAL_8N1, MODEM_RX, MODEM_TX);
delay(3000);
// Restart SIM800 module, it takes quite some time
// To skip it, call init() instead of restart()
SerialMon.println("Initializing modem...");
modem.restart();
// use modem.init() if you don't need the complete restart
// Unlock your SIM card with a PIN if needed
if (strlen(simPIN) && modem.getSimStatus() != 3 ) {
modem.simUnlock(simPIN);
}
// You might need to change the BME280 I2C address, in our case it's 0x76
if (!bme.begin(0x76, &I2CBME)) {
Serial.println("Could not find a valid BME280 sensor, check wiring!");
while (1);
}
// Configure the wake up source as timer wake up
esp_sleep_enable_timer_wakeup(TIME_TO_SLEEP * uS_TO_S_FACTOR);
}
void loop() {
SerialMon.print("Connecting to APN: ");
SerialMon.print(apn);
if (!modem.gprsConnect(apn, gprsUser, gprsPass)) {
SerialMon.println(" fail");
}
else {
SerialMon.println(" OK");
SerialMon.print("Connecting to ");
SerialMon.print(server);
if (!client.connect(server, port)) {
SerialMon.println(" fail");
}
else {
SerialMon.println(" OK");
// Making an HTTP POST request
SerialMon.println("Performing HTTP POST request...");
// Prepare your HTTP POST request data (Temperature in Celsius degrees)
String httpRequestData = "api_key=" + apiKeyValue + "&value1=" + String(bme.readTemperature())
+ "&value2=" + String(bme.readHumidity()) + "&value3=" + String(bme.readPressure()/100.0F) + "";
// Prepare your HTTP POST request data (Temperature in Fahrenheit degrees)
//String httpRequestData = "api_key=" + apiKeyValue + "&value1=" + String(1.8 * bme.readTemperature() + 32)
// + "&value2=" + String(bme.readHumidity()) + "&value3=" + String(bme.readPressure()/100.0F) + "";
// You can comment the httpRequestData variable above
// then, use the httpRequestData variable below (for testing purposes without the BME280 sensor)
//String httpRequestData = "api_key=tPmAT5Ab3j7F9&value1=24.75&value2=49.54&value3=1005.14";
client.print(String("POST ") + resource + " HTTP/1.1\r\n");
client.print(String("Host: ") + server + "\r\n");
client.println("Connection: close");
client.println("Content-Type: application/x-www-form-urlencoded");
client.print("Content-Length: ");
client.println(httpRequestData.length());
client.println();
client.println(httpRequestData);
unsigned long timeout = millis();
while (client.connected() && millis() - timeout < 10000L) {
// Print available data (HTTP response from server)
while (client.available()) {
char c = client.read();
SerialMon.print(c);
timeout = millis();
}
}
SerialMon.println();
// Close client and disconnect
client.stop();
SerialMon.println(F("Server disconnected"));
modem.gprsDisconnect();
SerialMon.println(F("GPRS disconnected"));
}
}
// Put ESP32 into deep sleep mode (with timer wake up)
esp_deep_sleep_start();
}
Before uploading the code, you need to insert your APN details, SIM card PIN (if applicable) and your server domain.
Important: Most hosting services require you to make HTTPS requests. This code is not compatible with HTTPS. So, to make it work, you need to disable the HTTPS on your server or enable both HTTP and HTTPS(contact your hosting provider). Even though this board supports HTTPS requests, we couldn’t make it work. Nonetheless, you can try out this example sketch and see if it works for your board to make HTTPS requests: SIM800L HTTPS Client.
How the Code Works
Insert your GPRS APN credentials in the following variables:
const char apn[] = ""; // APN (example: internet.vodafone.pt) use https://wiki.apnchanger.org
const char gprsUser[] = ""; // GPRS User
const char gprsPass[] = ""; // GPRS PasswordIn our case, the APN is internet.vodafone.pt. Yours should be different. We’ve explained previous in this tutorial how to get your APN details.
Enter your SIM card PIN if applicable:
const char simPIN[] = ""; You also need to type the server details in the following variables. It can be your own server domain or any other server that you want to publish data to.
const char server[] = "example.com"; // domain name: example.com, maker.ifttt.com, etc
const char resource[] = "/post-data.php"; // resource path, for example: /post-data.php
const int port = 80; // server port numberIf you’re using your own server domain as we’re doing in this tutorial, you also need an API key. In this case, the apiKeyValue is just a random string that you can modify. It’s used for security reasons, so only anyone that knows your API key can publish data to your database.
The code is heavily commented so that you understand the purpose of each line of code.
The following lines define the pins used by the SIM800L module:
#define MODEM_RST 5
#define MODEM_PWKEY 4
#define MODEM_POWER_ON 23
#define MODEM_TX 27
#define MODEM_RX 26
#define I2C_SDA 21
#define I2C_SCL 22Define the BME280 I2C pins. In this example we’re not using the default pins because they are already being used by the battery power management IC of the T-Call ESP32 SIM800L board. So, we’re using GPIO 18 and GPIO 19.
#define I2C_SDA_2 18
#define I2C_SCL_2 19Define a serial communication for the Serial Monitor and another to communicate with the SIM800L module:
// Set serial for debug console (to Serial Monitor, default speed 115200)
#define SerialMon Serial
// Set serial for AT commands (to SIM800 module)
#define SerialAT Serial1Configure the TinyGSM library to work with the SIM800L module.
// Configure TinyGSM library
#define TINY_GSM_MODEM_SIM800 // Modem is SIM800
#define TINY_GSM_RX_BUFFER 1024 // Set RX buffer to 1KbInclude the following libraries to communicate with the SIM800L.
#include <Wire.h>
#include <TinyGsmClient.h>And these libraries to use the BME280 sensor:
#include <Adafruit_Sensor.h>
#include <Adafruit_BME280.h>Instantiate an I2C communication for the SIM800L.
TwoWire I2CPower = TwoWire(0);And another I2C communication for the BME280 sensor.
TwoWire I2CBME = TwoWire(1);
Adafruit_BME280 bme; Initialize a TinyGSMClient for internet connection.
TinyGsmClient client(modem);Define the deep sleep time in the TIME_TO_SLEEP variable in seconds.
#define uS_TO_S_FACTOR 1000000 /* Conversion factor for micro seconds to seconds */
#define TIME_TO_SLEEP 3600 /* Time ESP32 will go to sleep (in seconds) 3600 seconds = 1 hour */In the setup(), initialize the Serial Monitor at a baud rate of 115200:
SerialMon.begin(115200);Start the I2C communication for the SIM800L module and for the BME280 sensor module:
I2CPower.begin(I2C_SDA, I2C_SCL, 400000);
I2CBME.begin(I2C_SDA_2, I2C_SCL_2, 400000);Setup the SIM800L pins in a proper state to operate:
pinMode(MODEM_PWKEY, OUTPUT);
pinMode(MODEM_RST, OUTPUT);
pinMode(MODEM_POWER_ON, OUTPUT);
digitalWrite(MODEM_PWKEY, LOW);
digitalWrite(MODEM_RST, HIGH);
digitalWrite(MODEM_POWER_ON, HIGH);Initialize a serial communication with the SIM800L module
SerialAT.begin(115200, SERIAL_8N1, MODEM_RX, MODEM_TX);Initialize the SIM800L module and unlock the SIM card PIN if needed
SerialMon.println("Initializing modem...");
modem.restart();
// use modem.init() if you don't need the complete restart
// Unlock your SIM card with a PIN if needed
if (strlen(simPIN) && modem.getSimStatus() != 3 ) {
modem.simUnlock(simPIN);
}Initialize the BME280 sensor module:
if (!bme.begin(0x76, &I2CBME)) {
Serial.println("Could not find a valid BME280 sensor, check wiring!");
while (1);
}Configure deep sleep as a wake up source:
esp_sleep_enable_timer_wakeup(TIME_TO_SLEEP * uS_TO_S_FACTOR);Recommended reading: ESP32 Deep Sleep and Wake Up Sources
In the loop() is where we’ll actually connect to the internet and make the HTTP POST request to publish sensor data. Because the ESP32 will go into deep sleep mode at the end of the loop(), it will only run once.
The following lines connect the module to the internet:
SerialMon.print("Connecting to APN: ");
SerialMon.print(apn);
if (!modem.gprsConnect(apn, gprsUser, gprsPass)) {
SerialMon.println(" fail");
}
else {
SerialMon.println(" OK");
SerialMon.print("Connecting to ");
SerialMon.print(server);
if (!client.connect(server, port)) {
SerialMon.println(" fail");
}
else {
SerialMon.println(" OK");Prepare the message data to be sent by HTTP POST Request
String httpRequestData = "api_key=" + apiKeyValue + "&value1=" + String(bme.readTemperature())
+ "&value2=" + String(bme.readHumidity()) + "&value3=" + String(bme.readPressure()/100.0F) + "";Basically, we create a string with the API key value and all the sensor readings. You should modify this string depending on the data you want to send.
The following lines make the POST request.
client.print(String("POST ") + resource + " HTTP/1.1\r\n");
client.print(String("Host: ") + server + "\r\n");
client.println("Connection: close");
client.println("Content-Type: application/x-www-form-urlencoded");
client.print("Content-Length: ");
client.println(httpRequestData.length());
client.println();
client.println(httpRequestData);
unsigned long timeout = millis();
while (client.connected() && millis() - timeout < 10000L) {
// Print available data (HTTP response from server)
while (client.available()) {
char c = client.read();
SerialMon.print(c);
timeout = millis();
}
}Finally, close the connection, and disconnect from the internet.
client.stop();
SerialMon.println(F("Server disconnected"));
modem.gprsDisconnect();
SerialMon.println(F("GPRS disconnected"));In the end, put the ESP32 in deep sleep mode.
esp_deep_sleep_start();Upload the Code
After inserting all the necessary details, you can upload the code to your board.
To upload code to your board, go to Tools > Board and select ESP32 Dev module. Go to Tools > Port and select the COM port your board is connected to. Finally, press the upload button to upload the code to your board.
Note: at the moment, there isn’t a board for the T-Call ESP32 SIM800L, but we’ve selected the ESP32 Dev Module and it’s been working fine.
Demonstration
Open the Serial Monitor at baud rate of 115200 and press the board RST button.
First, the module initializes and then it tries to connect to the internet. Please note that this can take some time (in some cases it took almost 1 minute to complete the request).
After connecting to the internet, it will connect to your server to make the HTTP POST request.
Finally, it disconnects from the server, disconnects the internet and goes to sleep.
In this example, it publishes new sensor readings every 60 minutes, but for testing purposes you can use a shorter delay.
Then, open a browser and type your server domain on the /esp-chart.php URL. You should see the charts with the latest sensor readings.
Troubleshooting
If at this point, you can’t make your module connect to the internet, it can be caused by one of the following reasons:
- The APN credentials might not be correct;
- The antenna might not be working properly. In our case, we had to replace the antenna;
- You might need to go outside to get a better signal coverage;
- Or you might not be supplying enough current to the module. If you’re connecting the module to your computer using a USB hub without external power supply, it might not provide enough current to operate.
Wrapping Up
We hope you liked this project. In our opinion, the T-Call SIM800 ESP32 board can be very useful for IoT projects that don’t have access to a nearby router via Wi-Fi. You can connect your board to the internet quite easily using a SIM card data plan.
We’ll be publishing more projects about this board soon (like sending SMS notifications, request data via SMS, etc.) so, stay tuned!
You may also like:
- $11 TTGO T-Call ESP32 with SIM800L GSM/GPRS (in-depth review)
- ESP32/ESP8266 Insert Data into MySQL Database using PHP and Arduino IDE
- ESP32/ESP8266 Plot Sensor Readings in Real Time Charts – Web Server
- ESP32 Web Server with BME280 – Advanced Weather Station
Learn more about the ESP32 with our resources:
- Learn ESP32 with Arduino IDE (Course)
- MicroPython Programming with ESP32 and ESP8266 (eBook)
- More ESP32 Projects and Tutorials
Thanks for reading.
Muito Obligado Rui, thanks very much, can we see in a video how do you insert the SIM card in the board?
Also an idea, what about a simple app using app.inventor to send an SMS to this board and according to the SMS it checks a specific sensor and then it sends an SMS back, so the board gets the message and the phone number that sends the request to know the status of a sensor, for example someone wants to know the humidity or the temperature of a far away garden, or send a command to open a valve for 5 seconds for water, and with this we can send commands without the need of a router, which is GREAT !!!! THANKS AGAIN
Hi Tomas.
We’ll post more tutorials about this board: show how to make things happen by sending SMS and request data via SMS.
So, stay tuned.
Thank you for following our work.
Regads,
Sara
Make tutorial about Biometric Attendance System using Fingerprint Sensor and this board.
Thanks for the suggestion!
Can you please make a tutorial on how to use sim800l (of TTGO T-Call) to control gpio pins instead of esp32 for controlling led or realy.
I really liked your tutorials and thanks for such good tutorials.
Hi.
You can use the same code you would use on a regular ESP32 to control GPIOs.
Regards,
Sara
Parabéns pelo trabalho e feliz ano novo
Muito Obrigada 🙂
Olá Sara e Rui,
Estou usando a TTGO TCall a algum tempo sem usar a biblioteca TinyGSM que vem apresentando problemas, contudo venho fazendo requisicoes HTTP GET com sucesso, contudo, preciso fazer POST em vez de GET e não estou tendo exito com os comandos:
dados=”fname=John&lname=Doe”;
url=”ttgo.requestcatcher.com”;
AT+SAPBR=1,1
AT+SAPBR=2,1
AT+HTTPINIT
AT+HTTPPARA=CID,1
“AT+HTTPPARA=URL,\”” + url+”\””
“AT+HTTPPARA=\”USERDATA\”,\””+dados+”\””
“AT+HTTPPARA=\”CONTENT\”,\”application/x-www-form-urlencoded\””
“AT+HTTPDATA=” + String(dados.length()) + “,5000”
AT+HTTPACTION=1
A requisição chega em branco no servidor. alguma ideia?
Excellent as usual
Congratulations.
I was thinking on doing something very similar but with yur tutorial, things will be much easier and fast.
Great saved me hours and hours.
carlos Frondizi
Hi Carlos.
That’s great! Thank you for following our work 😀
Regards,
Sara
Thanks for the very good tutorial. I recently purchased a t-call and was a bit fazed by the documentation. This has spelled it out perfectly. One thought I have had is, if it takes up to one minute to connect to the internet, the esp32 could be awake for up to 50% of the time. Depending on the currency of the data required, it could simply take a reading once a minute, for say 10 minutes and then connect to upload all 10 data points.
This would require keeping a counter of where in the cycle of 10 readings it is. EEPROM I guess would be the best place to keep that variable.
This way uptime would be reduced to about 12%.
Thanks for the great resource.
Do you have a source for the improved antenna?
Hi Paul.
I’ve just added a link to the antenna in the parts required.
Regards,
Sara
Thanks, Sara……Paul
Ótimo tutorial Sara e Rui,
Voces podem nos informar qual o tamanho do pacote de dados, em bytes, enviado em um dia ?
———————————————————————————————
Great Tutorial Sara and Rui,
Can you tell us the data packet size send in one day ?
Hi, the SIM800L only support 2G right? Any possibilities we can the same code for GSM module with 3G/4G connection for improve speed. Thanks.
By the way, great tutorial as always!!
Hi Umar.
That’s right.
The code should be compatible with other modules with just a few changes for proper initialization.
See the TinyGSM library documentation: github.com/vshymanskyy/TinyGSM
Regards,
Sara
Hello Sara and Rui!
A big thanks for your very informative and well organised instruction videos!
At present I am working with the TTGO T-Call unit, and sending data works perfect. I am very interested to know how data can be sent using JSON; do you plan an introductory video on that in the (hopefully near) future?
Regards, Hans
As per other comments, this device and the variants of the Sim 900 are 2G devices and this service is no longer available in my country (Australia) and several others so please also include projects that use 3G or 4G as well
Regards
Phil
Hi Phill.
I’ve added a big note at the beginning of the post about that.
This board is 2G, that’s why it is so cheap compared with other 3G and 4G modules (tha cost between 25$ and 50$ just the module without ESP32).
Unfortunately, 2G is not supported in all countries.t
But, if you want to use a 3G and 4G module, most of the code should be compatible. The TinyGSM library is compatible with a wide variety of modules. You just need to initialize the module with the proper configurations.
We’ll take a look at some 3G and 4G modules and probably create some tutorials in the future.
Regards,
Sara
Hi Sara – I have only been able to find shields or devices for much more than that, closer to $70-80. Do you have recommendations for any cheaper boards/modules I can use that support LTE (as 3G is on its way out too it seems). Thanks!
store.arduino.cc/usa/arduino-mkr-nb-1500
Hi Jeff.
Unfortunately, 4G Shields are very expensive. Around 60$ to 80$.
I couldn’t find anything cheaper.
Regards,
Sara
When the ESP is in deep sleep, are the ancillary devices unit powered down on this device (GSM module, Serial to USB module etc)? Thinking about optimum battery life for in the field devices… Thanks.
To be honest we still need to do more power consumption tests with this board, but you should be able to lower quite significantly with deep sleep as used in this project
Olá, acabou de chegar minha TTGO T-Call ESP32 SIM800L, carregar este firmware o ESP32 fica eternamente dando a seguinte mensagem de erro, em que essa mensagem vai se repetindo sem parar:
Rebooting…
ets Jun 8 2016 00:22:57
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0018,len:4
load:0x3fff001c,len:956
load:0x40078000,len:0
load:0x40078000,len:13076
entry 0x40078a58
assertion “false && “item should have been present in cache”” failed: file “/Users/ficeto/Desktop/ESP32/ESP32/esp-idf-public/components/nvs_flash/src/nvs_item_hash_list.cpp”, line 85, function: void nvs::HashList::erase(size_t)
abort() was called at PC 0x400d1283 on core 0
Backtrace: 0x4008704c:0x3ffc62c0 0x4008714b:0x3ffc62e0 0x400d1283:0x3ffc6300 0x400e3b20:0x3ffc6330 0x400e3e8e:0x3ffc6350 0x400e41bd:0x3ffc63a0 0x400e3934:0x3ffc6400 0x400e3776:0x3ffc6450 0x400e380f:0x3ffc6470 0x400e385a:0x3ffc6490 0x400e1054:0x3ffc64b0 0x400e1003:0x3ffc64d0 0x400d1b6e:0x3ffc6500
Você sabe como eu poderia solucionar esse problema?
Desculpe pelo post no outro tutorial que não era este
Hi Eduardo.
Those kind of errors are very difficult to troubleshoot.
Sometimes the ESP32 keeps rebooting when we don’t provide enough power.
For example, if you’re using a USB hub, it may not provide enough current. Or try another USB port.
At the moment, I don’t know what exactly can cause that problem.
Regards,
Sara
Hi Sara and Rui!
Congratulations for your tuto.
Im asking about make a mesh network using this module as root node, avoiding to use a router.
It would be posible?
Thanks for your Job.👌
Olá Eduardo, se você não modificou o código, verifique além de onde está sua placa, num hub usb ou na USB do computador, o chip precisa de muita corrente pra funcionar. Pelo log parece que seu programa não pode ser gravado totalmente. Sei que tem um plugin para Arduino que interpretar esse backtrace e indica onde está o erro no código.
https://github.com/me-no-dev/EspExceptionDecoder
Muito Obligado, I am from El Salvador, and I have a couple of ideas, I found today this “GSM Module SIM800L With MIC & 3.5mm Headphone Jack” is it possible to integrate with the ESP32 to create a very simple mobile?
Here are the ideas:
– voice to text. Sends a verbal instruction from a mobile to an ESP32
– text to voice. An ESP32 sends a SMS to another ESP32, like a temperature warning, but you don’t need to check incoming SMS because you will use speakers.
Hi Sara & Paul,
Great project, and well explained.
Im thinking of using this for my (snail) mailbox , so i can a notification when i receive my newspaper or letters. (my mailbox is far away from my home)
So i will use a small switch to trigger when the mailbox receives mail
Question : how do i set it up that it triggers IFTTT, or will you do a tutorial on that ?
I use Domoticz and that can receive triggers from IFTTT
keep up the good work
Hi Charles.
You can take a look at these tutorials and see if they help.
https://randomnerdtutorials.com/esp32-esp8266-publish-sensor-readings-to-google-sheets/
https://randomnerdtutorials.com/door-status-monitor-using-the-esp8266/
You just need to make an HTTP post request on the right webhooks URL.
Instead of searching for google sheets in the first tutorial, search for “email”
In both cases, I recommend searching for email as people were reporting some problems with the “gmail” option.
Regards,
Sara
P.S. It’s Sara and Rui (not Paul) 😀
Hi,
The SIM800L module is very power hungry and needs up to 2A (Amperes) when transmitting. The module will reboot and blink 7-8 times when the voltage is dropping due to insuffient Power. This is well described in the datasheet for the SIM800L. Use a Lipo battery charger and Lipo battery to Power this Board. A fully charged Lipo will give 4.1 Volts which is optimal for the SIM800.Max voltage is around 4.3-4.4 volts and it will send out a Message if the voltage is to high.
I also put a 1000 micro Farad capacitor between + and – Close to the module. Datasheets can be very useful for practical use of all kinds of modules and parts.
how i can connect this module with lora module plz ?
Many thanks Rui and Sara for another great tutorial, you have taught me a lot about the TTGO T-Call in an easy and understandable manner. My first remote air quality system using this module has been running well and collecting data.
With my new knowledge I have now successfully migrated over to using a SIM7000G module with NB IoT and an ESP32.
Eagerly awaiting another project!
Hi Richard.
Rui show me your project and it looks great!
Congratulations!
It’s very rewarding see what our readers can build with our tutorials.
Best wishes.
Sara 😀
Hey Richard,
Can you post the differences in the code between the T-call and SIM7000G?
The T-Call connects to (modem.gprs), does the SIM7000 connect to (modem.lte)?
Hi Richard,
Do you mind sharing your code for the Sim 7000g?
Hi Adam,
It’s been a long time since I did this project and the system is still up and running nicely. The SIM7000G board is connected to an ESP32, here are the relevant bits of code that if I remember correctly are different from the TTGO unit.
#define TINY_GSM_MODEM_SIM7000
#define TINY_GSM_RX_BUFFER 1024
#include <HardwareSerial.h>
#include <TinyGsmClient.h>
HardwareSerial SerialAT(1);
#define modemPwKey 23
#define modemTx 17
#define modemRx 16
TinyGsm modem(SerialAT);
TinyGsmClient client(modem);
const char apn[] = “cmnet”; //China Mobile
const char gprsUser[] = “”; //For China Mobile no user required
const char gprsPass[] = “”; //For China Mobile no password required
void setup() {
Serial.begin(115200);
pinMode(modemPwKey, OUTPUT);
digitalWrite(modemPwKey, LOW);
SerialAT.begin(115200, SERIAL_8N1, modemRx, modemTx);
delay(3000);
modemStart();
}
If you have any problems or need help just let me know.
Richard
Hi Sir, can i use this code for DHT11 sensor to send data to googlesheet?
Nice tutorial!
Can anyone help me out and tell me can the TTgo T-call be powered by the 5 v pin, or that pin is for 5 v input! I’m asking because i ordered an USB C converter from Banggood and my bag was empty, the support was rude, and i lost my money ! So now no usb connection, i must use the rx tx onboard and i must power it somehow! Thanks
Hi Zoli.
Yes, you can use the 5V pin for power.
Regards,
Sara
Like Sara said, you can use the 5V pin to power your device. There is one downside to this though. Powering your TTGO ESP32 SIM800L this way does not allow charging of the battery via the on-board battery connector. This feature is only available when powered via USB-C.
Yes, it’s true.
Thanks for pointing that out.
Hi Sarah, hi Riu,
i tryed to upload a sketch, but doesn’t work anywell.
While loading, I keep the button pressed, but it doesn’t work.
i’d like to connect à 10µF capacitor, but there is’nt EN pin on the board.
I prefer not to weld directly on the board.
Have you an idea how to do this?
Thank you 🙂
Hi.
You just need to press the button once. You don’t need to hold the button.
I don’t know what might be causing the issue.
Regards,
Sara
Hi, thank you, i found how does the TTGO-Call woks. 🙂
Hi Sara, Firstly thank you for the amazing tutorials, they have taught me a lot.
Having said that though, with my limited coding knowledge, I have been trying to replace the HTTP post method above to rather work with a MQTT broker that requires a username and password. Any pointers you can give me here on how to do this to the example above would be greatly appreciated.
Looking at your other tutorials with MQTT I also could not find an example where the MQTT broker requires a username and password. Thank you in advance for any assistance. Many Thanks
Hi Ryan.
I think this publication explains what you’re looking for: https://rntlab.com/question/how-to-use-cloud-mqtt-broker-with-esp32-using-async-mqtt-client-library/
Regards,
Sara
Thank you for the speedy reply. That’s a great resource – thank you! Now to figure out how to make it work with the sketch above…
Thanks again
Hello again, Sara and Rui, great tutorial as usual even if we might not have 2G for long here in the Philippines. I suppose I can interface an ESP32 with some LTE module to get the same result.
As an aside, T-Call implies that it can do voice calls. Have you tested that? Can’t find anything in the tech docs, but then I haven’t looked that closely.
Lastly, what software or app did you use to create that neat Schematic Diagram, which shows up at 3:37 in the video tutorial and again toward the middle of this post?
Thanks again, and regards
Hi Rui, I am trying to connect to Google’s FireBase, but it is impossible, among other things I don’t know how to connect with the API key that they give me. What should i do to connect to the SIM800L? thanks for this tutorial.
Hi Sara, I am trying to connect to Google’s FireBase, but it is impossible, among other things I don’t know how to connect with the API key that they give me. What should i do to connect to the SIM800L? thanks for this tutorial.
Hi Alberto.
Unfortunately, we don’t have any tutorial about FireBase.
I’m sorry.
Regards,
Sara
did you get any code to connect ttgo-t-call board to firebase ? if so please share, i am need of it very much.
Greetings, thanks for the tutorial.
Can I connect two 18650 lithium batteries in parallel to the module (TTGO T-Call ESP32 SIM800L)? Can the power manager supply enough current to charge the two batteries in parallel?
I can’t see why not. The max charge current is limited to 500ma though, so they will just take some time to charge. It will take approximately 1-hour of charge for every 500mAh of battery power consumed.
can we use a 4G sim card in this or only 2G/3G
Hi.
You can use 4G card.
Regards,
Sara
You can use a 4G SIM card but the TTGO T-Call is only a 2G module. If you want 4G then change to a SIM7000 series, you can use the same code but there are some GPIO changes.
I use a 4G SIM successfully. The SIM800 only supports 2G connections though, so as long as your service provider still supports 2G, you will be fine.
That’s right.
Hi, is it possible to post an image (.jpg file) as part of the http post request?
Thanks
Paulo
In the examples, you say not to use the default I2C pins as these are used by power management. Why would this pose a problem, seeing as I2C connected devices each have their own unique address? I am asking this because I have run into some strange behaviour trying exactly this, even with external discreet pull-up resistors added on the default SCL and SDA. It is easy enough to create a second I2C interface (thanks to your example!), but I would like to understand what the problem is.
Hi.
You can use the same I2C address without any problem.
You can learn more about I2C with the ESP32 here: https://randomnerdtutorials.com/esp32-i2c-communication-arduino-ide/
Thank you for your comment.
Regards,
Sara
Hi Rui, do you know whether can we communicate with an https server using TinyGSM library? According to Github project page, it supports SSL. But I couldn’t find an example code as to how to get it done.
Hi.
At the moment, we don’t have any tutorials about that subject.
Regards,
Sara
hello Sara, AWS Amazon uses SSL for Iot Core, correct? Did you ever make that kind of connection? It’s possible? Do you indicate any tutorial?
Hello Lakmal, I’m also interested in communicating to an https server, have you managed to achieve this? It seems like there is very little documentation on this.
Hya,
Also looking for a HTTPS connection solution for the esp32. Proving a difficult one to resolve!
Hi !!
Vey nice example. Also looking for a HTTPS connection solution for the esp32
Hi.
See Rui’s answer to this question: https://rntlab.com/question/how-to-connect-esp8266-to-ifttt-using-https-using-certificate/
Regards,
Sara
Is it possible to establish a connection between TTGO T-call and aws IoT with SIM800L?!
Hi.
Yes, I think it should be possible.
Regards,
Sara
Hi Sara and Rui, thanks for this brilliant tutorial.
I tried this on my ttgo t-call module and it worked like a charm.
I just wanted to send an image (i.e. a file) instead of sensor data using http request. Can you help me with that?
Hi.
At the moment, we don’t have a tutorial about that.
We’ll publish something like that soon with an ESP32-CAM, that you can adapt to your board.
Regards,
Sara
+1
Very interested in using esp32-cam with sim to send an image over GPRS at preconfigured timings.
Hi Sara,
Congratulation for your nice project and description.
You inspired me to use http post method in my project, called “TALMOB”.
Which is an client-server based temperature logging and monitoring application. Was developed originally with TCP connection and python on server side…
Thank you for your great description!!!
That’s awesome!
Regards,
Sara
Great writeup!
ive trying to add second BME sensor. using the adafruits library i cant get the 2nd sensor reading (return 0).
both address already set (0x77 and 0x76) via ground and vcc
do you have any other good library that support this?
Hi.
Read this guide about I2C that explains how to use multiple sensors: https://randomnerdtutorials.com/esp32-i2c-communication-arduino-ide/
Regards,
Sara
It would be perfect to get version of connecting with cloud based MQTT broker via GPRS on TTGO T-Call ESP32 SIM800L
Hello, would you be able to provide a link to the antenna you used? I can’t seem to find one anywhere. Or if you can’t provide a link, what should I search to find one. Thanks!
Thanks for great tutorial. What board do you select in Arduino IDE to work with TTGO T-CALL?
Hi.
I used ESP32 Dev module.
Regards,
Sara
Hey, thank you for this tutorial!
I learned much. I have same question.
I want to connect another I2C in Two Wire, BH1750.
I need to use: Wire.begin(I2C_SDA_2, I2C_SCL_2, 400000);
to start the module.
But
If a use:
I2CPower.begin(I2C_SDA, I2C_SCL, 400000);
I2CBME.begin(I2C_SDA_2, I2C_SCL_2, 400000);
Wire.begin(I2C_SDA_2, I2C_SCL_2, 400000);
// Keep power when running from battery
bool isOk = setPowerBoostKeepOn(1);
SerialMon.println(String(“IP5306 KeepOn “) + (isOk ? “OK” : “FAIL”));
IP5306 always FAIL
I’m using
I2CPower.begin(I2C_SDA, I2C_SCL, 400000);
I2CBME.begin(I2C_SDA_2, I2C_SCL_2, 400000);
// Keep power when running from battery
bool isOk = setPowerBoostKeepOn(1);
SerialMon.println(String(“IP5306 KeepOn “) + (isOk ? “OK” : “FAIL”));
Wire.begin(I2C_SDA_2, I2C_SCL_2, 400000);
IP5306 always OK
But I think if it can prejudice the I2C Power
What is the right way to do this integration?
Thank you in advance for your attention
Hi.
Read this article to learn how to combine multiple I2C devices:
https://randomnerdtutorials.com/esp32-i2c-communication-arduino-ide/
Regards,
Sara
I david i have same problem how you connect BH1750 to t call board because when i use wire.begin sensor return first reading as. 0 how to use correct use of Both bme and Bh1750 at same time
hi Rui, nice tutorial, so basically this 800l only work on 2G, what if in my counry has higher like 4G?
if run only in 2G I think it will slow sent the data right?
Hi Devis.
I’m not sure, but I think that if your country doesn’t support 2G, it will not work,
Regards,
Sara
HI,
I follow your excelent tutorial but at the end I just receive 0 in my database.
Any suggestion what is the possible problem?
Thank you
Ciao Sara, and ciao Santos,
I hope you are very well.
I’d like to connect the TTGO T-Call to Telegram using the GSM, rather than the WIFI like in your tutorial for ESP32. Do you think is it possible? A tutorial on it would be very usefull, I’m not been able to find anything about it.
Hi.
Yes, I think it should be possible.
At the moment, we don’t ave any tutorial about that.
Regards,
Sara
Thanks for your answer Sara. In the meaning time I tried to modify the code for connecting the TTGO CALL to TELEGRAM, but it doesn’t work. I hope I’m wrong but perhaps the SIM800 modem does not support TLS 1.2
Merry Christmas.
Hi,
Thanks for another great tutorial…
This module also contains charting circuit for the connected LiPo battery through USB-C connector. Are there any way to connect e.g. a solar panel directly to the board for charging? Is the USB-C connector the only way to use the charging feature?
Thanks in advance
Michael
Hello Rui & Sara, Thanks very much for this great tutorial. I was thinking if there is a way how I can set up the data connection credentials (apn, gprs user, gprspass) through smart config instead of pre-programming the details. Do you have a tutorial on this?
Thanks very much for your support!
Sorry, I commented on the wrong article. This is right!
Hi, could you help me?
I made a schedule based on this to connect to Wunderground, but I am trying a problem, after a while the message sending stops. If you restart the ESP32 via USB, the sending returns, but by programming it remains locked and without sending messages. I realized that the connection step with the operator is the step that presents the error. Have you seen anything like that?
Hello Sara and Rui,
Thank u very much for your excellent tutorials.
Actually i’d like to send image captured by esp32 cam to server using simcom 800a
rather using wifi.
Can u please help me with this.
Hi Mr , did you find any solution ?
2G is pretty old, have you tried LTE on LilyGo Sim7000G?
I get the following error with 7000G;
#error “Please define GSM modem model”
Anyone had a similar issue with the 7000 G board?
Thanks,
MoZen
Hi , Did you solve it ?
I had this error. It was resolved when I added “#define TINY_GSM_MODEM_SIM7000” before including the library “#include <TinyGsmClient.h>”.
Hello Sara and Rui.
Is it possible to adapt this example to send data to Google Spreadsheets?
Hi.
Yes, I think that’s possible.
This tutorial might be helpful: https://randomnerdtutorials.com/esp32-esp8266-publish-sensor-readings-to-google-sheets/
Regards,
Sara
Thank you very much for the tutorial,
I have a problem that I cannot solve. I share it with you to see if you can help me.
I have gone through all the wiring steps and the board is working fine with some programs, but it failed to detect the sensors. When I test the “I2C Test” it only detects the following:
19: 46: 24.705 -> Scanning …
19: 46: 24.740 -> I2C device found at address 0x75!
19: 46: 24.775 -> done
But it doesn’t detect any sensor.
I have gone through the cabling several times and tested with the default pins for SDA and SCL (21 and 22) and others configured ad-hoc (18 and 19, following the example).
I have also seen the entire tutorial below multiple times:
https://randomnerdtutorials.com/esp32-i2c-communication-arduino-ide/
But it only detects 0x75 …
Does anyone know what may be happening?
Thanks a lot!
Dear Sara,
dear Ruiz,
first of all I would like to say Thank you! for your extraordinary work.
Although o also like “the guy with the swiss accent” a lot, “Great Scott”, Frans Lab, Mr. Carlson from his special “vacuum lab” and the magnificent bright folks that brought the ACG to life again… all of those (except Great Scott and Andreas Spiess), I stick with Randomnerdtutorials.
Your work leads to results. Real results in the perfect mixture between laziness and keep your nose to the grindstone. All in all wonderful.
When i want to create a system that gathers a bunch of sensor data in the field, I’m using your tutorials (especially the ones for ESP NOW).
I also tried your tutorials covering TTGO SIM800L, but with that my setup did not work, when using TINYGSM. That reboots all the time when trying the sketch.
SIM800-Parser
On http://www.aeq-web.com two Austrian guys use a low level approach with direct AT-Instructions. However the problem with that is, that it is kind of tricky to grab the results of instructions, such as “Give me the signal strengh.” or “Show me the ‘GPS’ corrordinates”.
Playful technology created a very interesting project
https://youtu.be/mbOHl2Cnemk?t=1323
with a parser to process output of SIM800L. However this is no tutorial. Little chance to pattern after…
Maybe there is a choice to cover the SIMXX00 again, or one of it`s relatives (with LTE).
This could be great for citizen data, because the coverage with TTN-LORA still is very low.
So, SIMXX00 is literally the only way to publish the data. In this respect thank you very much for your advice with the external antenna. It is astonishing how good the board works with the antenna that you mentioned. I was able to transfer data very realiable even from inside conrete basements, when my phone ceased to work.
Sorry for this far too long post and thank you again very much.
Hi Tony.
I think we have a board with LTE, but I didn’t have the time to experiment with it yet.
Thanks for your comment.
Regards,
Sara
Hi, may I know how do I send image to google drive using the combination of GSM module and ESP32-CAM? Is it possible to achieve it?
Hi, thanks for the nice and detailed tutorial, I have a question, is there any particular reason behind using separate I2C bus for the BME280 sensor?
No.
We could have used the same bus.
Regards,
Sara
hey can i use I2C bus for Neo7m GPS module also
Yes.
You can use several devices on the same I2C bus as long as each device has a unique I2C address.
To better understand, you can take a look at this tutorial: https://randomnerdtutorials.com/esp32-i2c-communication-arduino-ide/
Regards,
Sara
Hi – very useful tutorial, thanks.
However, I find that a sleep time of 3600 seconds doesn’t give any sleep time at all! My ESP32SIM800L simply wakes up straight after going to sleep.
I have investigated this and find that a delay of 2147 seconds seems to work; at least the system goes to sleep for a while…I haven’t waited for it to wake up. 2148 seconds reverts to no sleep time. 10,000 seconds gives some sleep, but again I haven’t actually waited for it to wake up to see if it actually sleeps for 10,000 seconds. I doubt that it does.
I’m guessing that the maximum sleep time would be 2^31 – 1 micro-seconds, i.e. the maximum positive value a long can hold. This evaluates to 2147.483647 seconds.
Upon further investigation, I find that the code in the Arduino/ESP32/DeepSleep/TimerWakeUp Example includes the line (line 22)
#define uS_TO_S_FACTOR 1000000ULL
In your code you have
#define uS_TO_S_FACTOR 1000000
This should be
#define uS_TO_S_FACTOR 1000000UL
so that the arithmetic is carried out as an unsigned long variable.
My code now works for a delay of 3600 seconds.
Hi Sara, hi Rui, thank you for the tutorial. I would like to send the data to Thingspeak, unfortunately I always get a Bad Request message. I have made the following adjustments:
// Server details
// The server variable can be just a domain name or it can have a subdomain. It depends on the service you are using
const char server[] = “api.thingspeak.com”; // domain name: example.com, maker.ifttt.com, etc
const char resource[] = “”; // resource path, for example: /post-data.php
const int port = 80;
String apiKey = “MYAPIKEY”;
String httpRequestData = “api_key=” + apiKey + “&field1=” + String(bme.readTemperature())
+ “&field2=” + String(bme.readHumidity()) + “&field3=” + String(bme.readPressure()/100.0F) + “”;
I tried to modify your tutorial to HTTP POST, but unfortunately I always get the error message. Can you tell me where the error is?
Regards, Phillip
Hi, very nice tutorial. Do you know if there is a way to detect if the power to the USB is active. I can check the battery voltage through PIN35 but cant find a way to check the USB voltage.
good day can you please help me.I need to monitor the battery voltage and dont know exactly how .
kind Regards Hansie
https://randomnerdtutorials.com/power-esp32-esp8266-solar-panels-battery-level-monitoring/
Muy bueno amigo, podés hacerlo con micropython al mismo proyecto, sería interesante. Saludos sigue así.
hi sara Arduino:
GPS_Tracker_with_ttgoesp32:26:74: fatal error: BlynkSimpleSIM800.h: No such file or directory
when i try to upload my coding its showing like this where i have inserted this library in the ide, but still getting this error. do u have this library with u?TQ
Hi,
Does this module has any power pin input (5v).
Thanl you for great tutorial.I have question. According to the schematic Spi pins mosi:gpio23 cs:gpio5 and sim800l uses 5 and 23 ,does it mean I can t use spi and sim800l at the same time?So,I have to remap spi pins ,right?
Hi.
If those pins are also being used by the SIM800 module, it is better to use other pins for the microSD card.
You can read this tutorial to learn how to use different pins: https://randomnerdtutorials.com/esp32-microsd-card-arduino/#sdcardcustompins
Regards,
Sara
Hi Rui and Sara,
Great tutorial.
I am using SIM800L with AT commands. Problem is my vendor APIs are HTTPS instead of HTTP.
I keep getting 601 or 603 or similar errors (DNS error etc) after sending the data via AT commands.
As well, the APIs are JSON based and need to post data via FormBody instead of string encoding. This is another headache which I will deal with later on :(.
May you confirm if SIM800L support HTTPS and if so point to any help locations please?
Hello, I used part of the code to send data from other sensors to thingspeak, but I only manage to send integer values and no decimal places, I have the variables in floating type and I also tried to pass them to string type, but I still cannot send numbers with decimals, any solution ? Thanks in advance
Hi Diego, I’ve been trying the same thing but I haven’t been able. Don’t know connect with thinkspeak.
Could you share the code .
Thanks in advance.
castrojm1 at gmail.com
Hello,
is it possible to set APN settings via SMS? If so, how? I want to use device on several countries with different SIM card, but I do not want to flash code every time.
Hi Rui & Sara,
I use the I2C scanner with UNO and return value of 0x76 for the BME280 but when connected to the ESP32 for this tutorial, it returned “Could not find a valid BME280 sensor, check wiring!
“.
please advise.
Hi.
Please double-check that you are using the right I2C pins.
Regards,
Sara
Sim800l is one of the greatest module ever!!!!
The project that you have done is also great!!!
Hi. Very good tutorial.
I have one problem. When i start the I2C communication for the SIM800L module and for the BME280 sensor module the ID show me the following error: call of overloaded ‘begin(int, int, int)’ is ambiguous
How can I solve this?
Thanks
Hi.
Are you using the same code we use in this tutorial or did you make any changes?
Regards,
Sara
Yes, I’m using exactly the same code.
Best regards
Hi.
I just compiled the code again, and it is working just fine for me.
I’m not sure what might be the issue.
Regards,
Sara
Hi thank you for this wonderful project,
I just have a problem is that I try different sim card and I encounter the same problem with the “APN connection faiI”,
I don’t know how to solve this
Hi.
It might be a problem related to the network provider.
I’m not sure…
Regards,
Sara
Thank you for your reply,
Is the esp32 code compatible with the new library update ” TinyGsmClient.h ” and i must to change the code ?
Hi.
I haven’t tried the new library yet.
The best place to get an answer about that is the library issues page: https://github.com/vshymanskyy/TinyGSM/issues
Regards,
Sara
#define DUMP_AT_COMMANDS
and share what you get here, we might be able to help.
OK
AT+CIPCLOSE=0,1
+CME ERROR: operation not allowed
AT+CIPSSL=0
OK
AT+CIPSTART=0,”TCP”,”****website*****”,80
OK
0, CONNECT FAIL
Connecting to ****website***
fail
check to see if the website is not HTTPS
Hi Ahmad
the website is in http, and I tried with both “http” and “https”, it gave me the same error
Hi there,
I would like to connect more DS18B20 digital temperature sensors. Can you help me how to extend the code?
Best regards
Manfred
Hi.
Check out this tutorial: https://randomnerdtutorials.com/esp32-multiple-ds18b20-temperature-sensors/
Regards,
Sara
Hi
Which library Wire are you using in this proyect.
Best Regards
I have the next error
Wire.h:80:10: note: candidate: ‘bool TwoWire::begin(uint8_t, int, int, uint32_t)’
bool begin(uint8_t slaveAddr, int sda=-1, int scl=-1, uint32_t frequency=0);
^~~~~
exit status 1
call of overloaded ‘begin(int, int, int)’ is ambiguous
Have to be the library right?
Regards
Olá Rui e Sara,
Desejo-vos bom 2022
Gostaria de talvez usar o módulo TTGO-Call só que necessito saber quantos pinos de entradas e para saídas estão disponíveis na placa assim existe além das Uarts usadas, se está disponível uma terceira. Paro o meu projeto necessito 5 pinos para saída e 12 pinos para entradas. Caso possam dar essa informação fico grato.
Obrigado
João
Olá.
Pode encontrar mais informação sobre a TTGO T-Call no proximo link includingo pinout : https://makeradvisor.com/ttgo-t-call-esp32-with-sim800l-gsm-gprs/
Esse website também é nosso.
Cumprimentos,
Sara
Hey, I am a fan of your YouTube channel and page, I am trying to transfer some data from PC (CodeSys or TIA portal) to nodemcu (ESP8266) using an ethernet module (ENC28J60). I have tried many times and failed. Since you are an expert in these, can you help me out if you have the time? much appreciated. thanks
Hi.
Unfortunately, I’m not familiar with that subject.
Regards,
Sara
Hello,
Thank you very much for your excelent work. I would like to ask you about using DHT22 sensor with this module. I have a problem when I start the tcall module by feeding it. Once I feed it, it does not start untill I put away the DHT22 sensor (I mean to unplug the feed of DHT22 sensor which is using the 5V output PIN of the tcall and I did also use the 3.3V PIN with the same results). Once the tcall is on I can connect again the DHT22 and it works perfectly forever. I have a lot of different ideas about how to solve it, but all of them include hardware modifications or power supply modification like powering the module and the sensor from the same power source and do not use the module power PINs.
Do you have any software solution for this problem? Or any kind of suggestion? I’m feeding it with enough current (tried from 1A to 4A) and 5V. The wiring is as simple as DATA to digital PIN12 and GND to GND PIN and VCC to 5V PIN (or 3.3V PIN).
Hi,
I need to connect to my server using https so, the code “(!client.connect(server, port))” won’t work with 443 as port number.
Is there a work around?
Thank you!!
Thank you for your wonderful resource, well written and tested!
I am using the TTGO T-Call ESP32 SIM800L for remote temperature monitoring. The code works perfectly but I wish to get an SMS alarm if the mains power is lost so that I can visit the site and restore power before the battery runs out. I can use a crude method by simply intercepting the 5v from the USB C connector via a breakout box but I guess that the IP5306 must have some sort of flag to say a charger is connected and this would be a more elegant and reliable solution. Are you aware of such a register and a method to read it? I see that the IP5306 register it is written to, (setPowerBoostKeepOn) but I can’t find out how to read the relevant register, if it exists, to tell me that the charger is connected. Any ideas, pointers etc please.
Can we use this library for A9G
Hi Sara and Rui,
I need understand some issues about TTGO board.
I made a webserver using TTGO TCall, but I like to server some html pages from GSM to permit i access a html page of the ttgo, like inside WiFi network.
To use the sim8000L I need use the tinyGSM only?
I tried send AT commands to serialAT but I have problems to read the serialAT response.
Hi.
No.
You can use the codes for a regular ESP32.
For example, you can use any web servers we have for the regular ESP32 on this board. Here are examples of web servers: https://randomnerdtutorials.com/?s=web+server
You just need to make sure you take a look at your board’s pinout which is a bit different from a regular ESP32.
Regards,
Sara
how to solve this error
HTTP/1.1 301 Moved Permanently
Date: Mon, 18 Apr 2022 12:54:25 GMT
Transfer-Encoding: chunked
Connection: close
Cache-Control: max-age=3600
Expires: Mon, 18 Apr 2022 13:54:25 GMT
301 moved,
Http 301 notification says. Your page is moved to a new address or to inform you that page now is HTTPS…
Open at web browser the page or try this test a n computer
Telnet http://www.myurl.com 80
You will see a prompt.
Type:
GET http://www.myurl.com HTTP1.1
You will see the 301 error and sometimes show the HTTPS URL to access with port 443 ou a new location to open.
maybe your page is HTTPS only now. Try change to HTTPS. Or use another URL.
First, congratulations on the article. It’s excellent.
Recently, in April 2022, I stayed in Lisbon and did a test with the TTGO T-Call V1.3 with Vodafone SIM, but it was unsuccessfully. TTGO T-Call V1.3 can’t be connected to a cell network with the APN specifications. I bought the Vodafone SIM at the shopping, so it is a common SIM card.
I did a successfully test on Brasil with Claro SIM card. So, the program and hardware are ok.
There are new APNs on the Vodafone Network? Can I use Hologram or Things Mobile SIM Cards with the TTGO T-Call V1.3?
Hi.
I have a vodafone SIM card and it worked fine with the TTGO T-Call.
As for the other cards, they should work, but I never experimented.
Regards,
Sara
Hi Sara.
Thank you.
Best regards.
Dionne
Olá Dionne. Saudações do Brasil. O SIM800L é até onde sei um chip 2G. Acredito que em Portugal as redes 2G foram banidas só restando 3G. Pergunta a qualquer operadora em Portugal para ter resposta. No Brasil ainda é possível usar 2G. É uma preocupação que um dia o 2G será desativado no Brasil. Como existe milhões de modems 2G em uso aqui, duvido que desativem no Brasil no médio prazo.
Em tempo: Vodafone don’t have 2G in many places in Portugal… Look: 2G is green at map.
In Europe they are disabling 2G to use same frequency to 5G….
SIM800L uses only 2G network!
https://www.nperf.com/pt/map/PT/-/813.Vodafone/signal/?ll=36.77895778557337&lg=-8.285985859122759&zoom=8
Hello,
what is the function mdoem.init()? where can I fint it?
Hi.
Check the library documentation: https://github.com/vshymanskyy/TinyGSM
Regards,
Sara
Hi,
Im tryign to modify the code to send data at 1Hz, how do I go about makign the piost request repetitively once the connection to the server has been made?
Hi!
I would like to know this program would work with LILYGO® TTGO T-SIM A767SA R2: according to the manufacturer, this card works on the 4G network in South America, among others.
Thanks.
Hi.
I’m not sure. That board is not on the list of the supported boards for that library: https://github.com/vshymanskyy/TinyGSM
Regards,
Sara
Adafruit BME280 Library v.2.x returns an error when compiling
What error?
sorry, I forgot to copy the error.
compiling on bme280 version 1.x is successful.
updating to bme280 version 2.x – immediately an error, for some reason on tinygsm
_https://pastebin.com/mEbmqQqr logs
Hi,
thanks for an amazing tutorial .
i am trying to read the battery status level with i2c address 0X78
but i always get 0 as output.
do you have any tutorial for knowing the battery status ?
Hi.
No. Unfortunately, at the moment, we don’t have any tutorials about that subject.
Check if it can successfully establish an I2C communication and that you’re reading on the right address and pins.
Regards,
Sara
This is a good article. Thanks! Things have changed and we need LTE and 5G. Even though the hardware is more expensive, a tutorial on it would be much appreciated. Do you have a timeline on that?
Hi.
You can check our new tutorials with the SIM7000G that supports LTE:
– Getting Started with LILYGO T-SIM7000G ESP32 (LTE, GPRS, and GPS)
– LILYGO T-SIM7000G ESP32: Get GPS Data (Latitude, Longitude, Altitude, and more)
Regards,
Sara
Hi Sara,
Thank you for the amazing tutorials,
I want to send an image from esp32cam to webserver via post method.
When I use Wi-Fi like your very good tutorial in
«https://randomnerdtutorials.com/esp32-cam-post-image-photo-server/#:~:text=Go%20to%20Tools%20%3E%20Board%20and,CAM%20on%2Dboard%20RST%20button. »,
it works without any problem, but the same code does not work when I use sim800L and Tinygsm when it connected to gprs and I get response code -3. I would be grateful if you could guide me, or if you have any experience in this field, please let me know.
Thanks
Hello, if you can make a tutorial that has firebase as a server, I would appreciate it a lot.
Regards
I’m trying to follow the example here. I’m stuck on a problem !client.connect(server, port) which cannot connect to Server, what should I do?
15:23:32.655 -> Network connected
15:23:32.655 -> Connecting to internet
15:23:41.581 -> GPRS status: connected
15:23:42.566 -> CCID:
15:23:42.566 -> IMEI: 862749052048427
15:23:42.566 -> Operator: Orange
15:23:42.602 -> Local IP: 10.3.72.157
15:23:42.602 -> Signal quality: 21
15:23:42.602 -> Connecting to asia-southeast1-line-alert-f78e1.cloudfunctions.net
15:23:42.637 -> … failed
Hi,
thank you for your amazing tutorial. I gave question regarding deep sleep. By default 3600 sec. When I change it to 10800 (3 hours) nothing happening. Device still sleep for 3600 (1 hour) or even start glitch and do two readings per hour. I wan to do 3 or 4 hours deep sleep. How I can do that?
Thank you,
Aday
Hello.
Excellent tutorial.
Could you please clarify something for me?
The power supply is done through the USB cable or the connector placed on the back of the board ?
Thank you very much.
Hi.
You can use both (but just one at a time).
The one at the back is to use with a 3.7V lithium battery
Regards,
Sara
Hello Sara
But why “…just one at a time…”? Is not through the USB cable that is possible to charge the 3.7V lithium battery?
I don’t think so.
But, I recommend searching for the board schematic diagram and checking how the circuit is built just to be sure.
Regards,
Sara
if you plug in the usb type C plus a battery, the board will power up by the usb and at the same time charging the battery. once you remove the usb cable, battery will take over.
Hi, I follow your guide and built 3 meteo station which works perfectly since almost 2 years with Bluehost. But suddenly, it stops working… The GET commande to the server failed with an error 301 (301 Moved Permanently
20:18:34.638 ->
20:18:34.638 ->
Moved Permanently
20:18:34.638 ->
The document has moved here.
)
I guess I need to program the esp32 to communicate directly to the port 443 but i’ml not sure, and till now I didn’t manage to do it yet. Any advices ???
hi Maxime, i also faced the same issue here. works perfectly for 2 months then suddenly get an error 301 (301 Moved Permanently)
hello I was wondering how can I use my ESP32 (TTGO T-Call ESP32 SIM800L) to Publish data in the cloud using micropython and also how can I do to connect my esp32 (TTGO T-Call ESP32 SIM800L)Cloud MQTT Broker
Hi.
Unfortunately, we don’t have this exmaple in micropython.
Regards,
Sara
Good morning,
Thank you for the project, I followed the course and the project works very well on my side, on the other hand I added a battery on the esp so that it is independent if there is a power cut, that said I would like to know if it is possible to raise the battery level to follow its loading and unloading?
Amine
Hello, can I ask if the ttgo T-call can be powered via 5v using the plastic connectors on the board??
hi , the tutorial you provide is useful. but i face an issue which is after the project function well for a month, I get a block by the server and get error 400 . The error last for 3 weeks. Do you face the same issue with me and do u have any solution for this ?
Hello thanks for instruction,
I tried your manual , with TTGO T-Call ESP32 SIM800H ( not SIM800L) but I have still issue with my sim card. I added the sim card tracking code and show me that : SIM card status: 1“
I want to ask for advice, how to fix this issue ?
I check my sim card – working correctly, data are available, 2G signal is full, also tried another SIM card the same issue, tried another antena – the same issue, PIN code is disabled, APN je správny.
Can you give me some advice please?
Hello! A few years ago I was using this project for my temperature sensors. I have reprogrammed my ESP32 but it gets stuck when connecting with the APN. I have checked that the SIM card works well and that there is 2G coverage. My country is Spain and 2G coverage continues to work. The error it returns is:
Initializing modem…
Connecting to APN: orangeworld fail
Thanks in advance
Hello!
Any suggestions or recommendations on updating this code for a T-SIM7670?
Wow, just what I needed! I’ve been struggling to find an example of how to publish data to the cloud without Wi-Fi using ESP32 and SIM800L. Your tutorial is PERFECT! I finally got it working and it’s saving me from a lot of headaches. Thank you!